Bring extra warmth to your wood with Medium Oak Wood Stain LCM500, a decorative finish designed for indoor wooden surfaces. Its balanced wood tone adds depth to furniture, beams, wall panelling and other interior woodwork without completely hiding the original appearance of the material. Available in matt or gloss finish, it lets you choose between a softer, more natural effect or a brighter decorative look. This wood stain can be applied in 1 to 3 coats to gradually adjust the depth of colour. Its coverage is approximately 10 m² per litre.
Key benefits of Medium Oak Wood Stain LCM500
Gives wood a warm and balanced Medium Oak tone.
Available in matt or gloss finish.
Specially designed for the protection and decoration of interior wood.
Helps preserve the natural visual character of the surface.
Ideal for furniture, beams, woodwork and wall panelling.
The colour can be adjusted with 1, 2 or 3 coats.
Short drying time between applications: 2 to 4 hours.
The finish is fully dry after approximately 24 hours.
One litre covers approximately 10 m².
The matt finish enhances a natural wood appearance while reducing reflections.
The gloss version gives the colour and grain a brighter, more decorative appearance.
Suitable for both renovation projects and the customisation of new wood.
How to apply Medium Oak Wood Stain LCM500
Prepare the surface
Start by making sure the wood is dry, clean and completely free from dust.
Old damaged or incompatible finishes should be removed before applying the stain.
If the surface is uneven, sand it appropriately to obtain a smooth and consistent base.
After sanding, carefully remove all sanding dust.
Old furniture or dirty woodwork should be properly cleaned before application to help prevent uneven absorption.
Apply the wood stain
Stir Medium Oak Wood Stain LCM500 thoroughly before starting.
Apply the product following the natural direction of the wood grain.
Apply 1 to 3 coats depending on the original colour of the wood and the desired finish.
Work evenly across continuous sections to maintain a consistent colour.
Avoid excess product, which may create differences in appearance.
Stir the stain regularly during use to help maintain an even colour throughout the application.
LCM500 is intended exclusively for indoor use.
Allow the correct drying time
Allow approximately 2 to 4 hours before applying the next coat.
Do not apply another coat while the surface is still damp or insufficiently dry.
After the final coat, allow approximately 24 hours for complete drying.
During this period, minimise handling and rubbing of the freshly treated surface.
Which finish should you choose: Medium Oak Matt or Gloss?
Matt finish for a more natural wood appearance
Medium Oak Matt Wood Stain LCM500 is ideal when you want a low-reflection surface with a look that remains close to natural wood. The colour remains visible without appearing overly pronounced, making it a suitable choice for sideboards, bookcases, beams or wall panelling.
This finish works particularly well with natural, warm, contemporary or more traditional interior styles.
Gloss finish to highlight colour and grain
With Medium Oak Gloss Wood Stain LCM500, more light is reflected from the surface. The colour appears more pronounced and the details of the wood become more visually noticeable.
This option may be preferred when you want to give more character to a piece of furniture or make decorative woodwork stand out. As with any tinted finish, the final result depends greatly on the wood species and its original colour.
How can you adjust the intensity of the Medium Oak colour?
With Medium Oak Wood Stain LCM500, the depth of colour can be adjusted gradually by applying between 1 and 3 coats.
1 coat is suitable when you simply want to warm up the original wood tone slightly.
2 coats create a more noticeable Medium Oak appearance.
3 coats further increase the visual depth when required by the surface or desired result.
Always allow 2 to 4 hours of drying time before adding another coat.
It is best to assess the colour once the coat has dried. A pale, highly absorbent wood will not react in the same way as a naturally darker or less porous species. These natural variations are part of the appearance of a finish that allows the wood itself to remain visually present.
How to maintain a Medium Oak finish
Everyday cleaning of stained wood
Remove dust regularly using a soft cloth.
For more noticeable marks, use a gentle cleaning method compatible with the finish.
Avoid abrasive sponges and aggressive cleaning methods that may alter the matt or gloss appearance.
Refreshing a worn or uneven surface
If the wood begins to show signs of wear over time, start by cleaning the affected area thoroughly.
Prepare the surface according to its condition before reapplying Medium Oak Wood Stain LCM500.
For a localised repair, carry out a small test first to check that the colour matches the existing finish.
Good practices before, during and after application
A few simple steps can help achieve a more even colour and avoid the most common application issues with Medium Oak Wood Stain LCM500:
Only work on a clean and sufficiently dry surface.
Stir the product thoroughly so that the colour is evenly distributed.
Always test the colour on a small area before treating the entire surface.
Take the original wood colour into account, as it remains visible and will influence the final result.
On larger surfaces, work consistently to avoid differences between already dry areas and freshly applied sections.
Allow 2 to 4 hours before applying an additional coat.
After the last coat, leave the finish to dry for approximately 24 hours.
Do not place objects or coverings directly onto the freshly stained surface.
Avoid repeated handling while the finish is drying.
Important: Medium Oak Wood Stain LCM500 is designed for interior wood. It is not intended for surfaces directly exposed to rain or outdoor conditions such as decking, fencing, cladding, garden buildings or shutters.
Tips for achieving a successful Medium Oak finish
Look at the wood first: its original colour plays a major role in the final appearance. A spare piece of the same wood species is ideal for testing.
Do not judge the colour while it is still wet: allow the first coat to dry before deciding whether an additional coat is necessary.
Keep the product well mixed: stir regularly so that the colour remains consistent throughout the project.
Follow the grain: your application strokes should follow the natural direction of the fibres rather than crossing them irregularly.
Match the finish to your interior: choose matt for a softer, more authentic look and gloss for greater shine.
Give furniture a new look with a Medium Oak finish
Pale wooden furniture can sometimes feel too neutral within an interior. Medium Oak Wood Stain LCM500 helps change its appearance without completely hiding its original identity. Instead of covering the material with an opaque colour, it allows the natural features of the wood to remain visible while adding a warmer overall tone.
It can be used to give more depth to a sideboard, chest of drawers, bookcase or older piece of furniture. The number of coats becomes a useful decorative tool: a single application for a subtle change, or additional coats for a stronger colour.
This gradual approach makes it easier to control the final result and helps avoid darkening the wood more than necessary from the first application.
What projects can Medium Oak Wood Stain LCM500 be used for?
The Medium Oak shade is particularly useful when you want to create a warm atmosphere without moving towards a very dark wood finish. It provides an easy-to-integrate middle ground between very pale tones and deeper browns.
On exposed beams, it can strengthen the visual presence of the wood within a room. On wall panelling, it can create a warmer and more enveloping atmosphere. On furniture, it can transform pale wood into a more visually distinctive decorative feature.
Choosing between matt and gloss makes it possible to refine the result even further. A matt finish emphasises subtlety and the natural character of the material, while a gloss finish draws more attention to the surface and its colour variations.
With coverage of approximately 10 m²/L, a drying time of 2 to 4 hours between coats and the possibility of applying up to 3 coats, LCM500 is suitable for both small furniture makeovers and larger decorative wood surfaces.
Why choose a Medium Oak wood stain instead of opaque paint?
These two finishes serve different decorative purposes. Paint is generally chosen when you want to completely transform the colour of a surface and create a more uniform appearance by largely hiding the original wood tones.
A Medium Oak wood stain is more suitable when you want the material to remain visually recognisable. It changes the colour while allowing some of the natural variations, grain and structure of the wood to remain visible.
LCM500 therefore makes it possible to refresh the appearance of interior wood without losing the features that give it character. It is particularly well suited to projects where the aim is to combine a warm wood tone, protection and enhancement of the natural material.
