Insecticide and fungicide treatment - Wood Bliss High-C

Wood Bliss® "high-C" is a curative and preventive wood treatment. It protects the wood against mould (basidiomycetes : Weeping Merula, Coniophore of cellars, Polypore of cellars, Poria valiant, Lenzite of fences, coriolus versicolor) and insects and termites. It protects the wood against the spread of fire and the formation of smoke. Available in 0.5, 1 and 5 L.

More Information.

Diagnostic
Complet

29,90 € tax incl.

In Stock - Shipped within 48H

Pests gnaw at the wood, causing a loss of mass and stability. Wood Bliss® fills the feeding corridors, strengthens cracked wood and thus replaces the lost wood mass. Among other things, the application of this product makes it possible to avoid expensive renovation techniques and the removal of infested wood.

The effect is immediate if the wood is attacked by harmful insects and mould. This product is an insecticide and fungicide treatment for wood.

Up to the depth of penetration, the product removes nutrients from the wood that are sought after by harmful insects. At the same time, it renders the wood unidentifiable to them so that after treatment, insects can no longer recognise the wood as a source of food. Thanks to its crystallisation effect, Wood Bliss® "high-C" provides the wood with protection against harmful pests.

Wood Bliss® "high-C" is a flame retardant wood treatment according to EN 13501: 1: B-S1-d0

 

 Advantages of Wood Bliss High-CAdvantages of Wood Bliss High-C

  • 50% reduction in toxic emissions

  • Immediate effectiveness

  • Contains no toxicologically questionable components.

  • Does not emit volatile organic compounds, except water.

 

WOOD BLISS HIGH-C GUIDEWOOD BLISS HIGH-C GUIDE

FIELDS OF APPLICATION

  • all categories of wood: frameworks, frames, beams, ...

  • all types of wood outdoors (in this case, protection against humidity is required)

  • on masonry

  • the food sector

  • in the environment of children, infants and people who are ill or suffering from allergies

  • dans l’environnement des animaux (écuries, étables, ruches, niches, cages, volières, …)

 

PREPARE THE WOOD

  • The support must be absorbent and healthy: clean, dry, non-greasy and dust-free.

  • Remove all water- and dirt-repellent substances, old paints, waxes and varnishes.

 

USE OF WOOD BLISS HIGH C

  • Shake the product before and during use

  • Apply at intervals of 12 hours by brush, roller, autoclave immersion, spray gun or injection.

  • Do not apply below 5°C (41F)

  • Do not glue treated pieces of wood together.

 

FIRE PROTECTION

  • Pre-treatment: 1 application of Wood Bliss®.

  • main treatment: 2 applications of Wood Bliss® "high-C".

 

mould treatment

  • Two applications of Wood Bliss

  • Depending on the extent and depth of the mould, then treat with Wood Bliss® "high-C".

 

ATTACK OF THE WOOD BY CAPRICORNS

  • Locate the infested parts (using a stethoscope if necessary)

  • Drill holes 2 to 3 mm in diameter, spaced about 3 cm apart up to the middle of the wood. Then inject Wood Bliss® "high-C" using a commercial type syringe and a long cannula. It is essential that the product reaches the infested areas. The holes drilled in the underside of the substrates to be treated must be sealed with wax or equivalent prior to treatment. If necessary, the wax can then be removed for the application of a decorative coating. If the attack is very extensive, it is advisable to remove the 3 old coats of protective coating and then apply Wood Bliss® in order to avoid possible outbreaks.

 

Drying

  • Complete after 48 hours

  • 12 to 16 hours between coats

 

tips Wood Bliss High CTIPS

Due to its strong alkalinity, a more or less important change of colour is observed (oak, chestnut, ...), test beforehand.

 

Composition Composition

  • Renewable vegetable raw materials. Contains no insecticides or biocides

  • abietic acid, potassium carbonate, silicate solution, cellulose, water, silicic acid, xylose

FunctionTreat
UseIndoor/Outdoor
Application supportAll supports
Types of woodAll kinds
Number of coats1 to 2 coats
Coverage10 to 15 m²/L per coat
Drying timecomplete after 48 hours - 12 to 16 hours between coats
Necessary ToolsSpalter, Brush, Sprayer
Cleaning of toolsWater
Product Compositionabietic acid, potassium carbonate, silicate solution, cellulose, water, silicic acid, xylose
ConservationStore in a cool, frost-free and dark place.
Avis des clients concernant ce produit

Write a review

Insecticide and fungicide treatment - Wood Bliss High-C

Insecticide and fungicide treatment - Wood Bliss High-C

Wood Bliss® "high-C" is a curative and preventive wood treatment. It protects the wood against mould (basidiomycetes : Weeping Merula, Coniophore of cellars, Polypore of cellars, Poria valiant, Lenzite of fences, coriolus versicolor) and insects and termites. It protects the wood against the spread of fire and the formation of smoke. Available in 0.5, 1 and 5 L.

More Information.